ISO80369-20 Pressure generator for Positive air pressure,Subatmospheric-pressure air, positive pressure liquid
Purchase list:
| 1 | Luer gauge | according to ISO80369-7-Figure C.1 Female reference luer lock connector for testing male luer connectors for leakage, separation from unscrewing, stress cracking and non-interconnectable characteristics |
| 2 | Luer gauge | according to ISO80369-7-Figure C.2 Male reference luer slip connector for testing female luer connectors for leakage, separation from axial load, stress cracking and non-interconnectable characteristics |
| 3 | Luer gauge | according to ISO80369-7-Figure C.3 Female reference connector for testing male luer lock connector for separation from axial load and resistance to overriding |
| 4 | Luer gauge | according to ISO80369-7-Figure C.4 Male reference luer lock connector for testing female luer connectors |
| 5 | Luer gauge | according to ISO80369-7-Figure C.5 Female reference luer slip connector for testing male luer connectors for leakage, separation from axial load, stress cracking and non-interconnectable characteristics |
| 6 | Luer gauge | according to ISO80369-7-Figure C.6 Male reference connector for testing female luer lock connector for separation from axial load and resistance to overriding |
| 7 | CONNECTOR ASSEMBLY DEVICE for ISO 80369-20 | The device is used to apply the required force and torque simultaneously when connecting a reference connector with a test sample. The device may also be used to apply a specified force-only or torque-only. Assembly Force : 26.5N - 27.5N Assembly Torque : 0.08 - 0.12Nm for lock connectors |
| 8 | pressure and positive-pressure liquid leakage tester | Control system Standard:ISO80369-20 Annex B and Annex C with mini printer. |
| 9 | Subatmospheric-pressure air leakage tester | Control system Standard:ISO80369-20 Annex D with mini printer. |
| 10 | Pressure generator | Positive air pressure,Subatmospheric-pressure air, positive pressure liquid |
| 11 | Resistance to separation from axial load tester | Standard:ISO80369-20 Annex F Measuring range:0-500N resolution：0.01N Force accuracy：＜±1% speed：10N/s Time:0-9999s with mini printer. |
iso 80369 test equipment. Kingpo supplies this as a calibrated laboratory item, machined or assembled in-house and inspected before despatch. It is built for the measurement named in the applicable standard, and it ships with a calibration certificate so it can be put straight into service.
What it is used for
- The measurement or dimensional check named in the applicable standard
- Repeatable set-up so results are comparable between runs and laboratories
- Documented output for the test report
Specification
| Item | iso 80369 test equipment |
| Material / construction | Hardened tool steel or stainless steel |
| Calibration | Calibration certificate supplied |
| Made by | Kingpo — machined, inspected and calibrated in-house |
Typical applications
- Third-party and notified-body testing, where the item has to be traceable to the standard
- Manufacturer incoming inspection and production release testing
- Design verification during development, before the protocol is frozen
How it is used
- Confirm the standard and clause you are testing against.
- Set the item up in the configuration the standard shows.
- Take the reading or run the sequence the standard specifies.
- Record the result with the sample identification and the calibration reference.
Care and calibration
Treat the item as an inspection tool rather than a production tool. Keep it clean and dry, store it protected, and re-calibrate on a cycle driven by how often it is used. Recording the item identity alongside every result is what makes a test report defensible later.
Buying notes
Send us the standard, the figure or clause number and the quantity. That is enough for us to quote and to tell you whether this is the right item for your protocol.
Frequently asked questions
Is a calibration certificate included?
Yes.
Can it be made to a customer drawing?
Yes — send the drawing and we will quote against it.
Which edition of the standard does it conform to?
Tell us the edition you are testing to and we will confirm before you order; editions differ and the dimensional limits are not always identical.
Do you ship spares or replacement parts?
Yes, for items we have built — send the item reference and we will identify the part.
Related gauges and equipment
Other equipment in the same range:
- ISO 80369-7 reference connector and ISO 80369-20 test apparatus
- ISO 80369-20 Medical Small Bore Connector Test Equipment,Medical testing equipment
- Automated Leakage By Pressure Decay Tester
Send the standard, figure number and quantity to Kingpo technical sales for a quotation and delivery date.
Parameters of the iso 80369 test equipment. Dimensions and limits are confirmed against the applicable standard before despatch.
| Standard | ISO 80369 |
| Item | iso 80369 test equipment |
| Construction | Bench instrument; details on the specification sheet |
| Scope of supply | Item and calibration certificate |
| Calibration | Calibration certificate supplied; re-calibration available |
| Origin | Kingpo — machined, inspected and calibrated in-house |
Custom versions, alternative materials and re-calibration are available. Send the standard, figure number and quantity for a quotation.